- TYRE BUILDING BLADDER
- CARCASS DRUM SLEEVE
- SHAPING DRUM SLEEVE
- SHAPING DRUM BLADDER
- PUSH OVER BLADDER
- TURN UP BLADDER
- TYRE CURING BLADDER
- AIR SPRING CURING BLADDER
- B TYPE SEMI-STEEL RADIAL TYRE CURING BLADDER FOR PCR & LTR
- C TYPE SEMI-STEEL RADIAL TYRE CURING BLADDER FOR PCR & LTR
- B TYPE ALL STEEL RADIAL TYRE CURING BLADDER FOR TBR
- A TYPE RADIAL TYRE CURING BLADDER FOR PCR & LTR
- AB TYPE RADIAL TYRE CURING BLADDER FOR PCR & LTR
- B TYPE CURING BLADDER FOR BIAS TRUCK & BUS (TBB) TIRE
- B TYPE CURING BLADDER FOR BIAS INDUSTRIAL & OTR TIRE
- B TYPE CURING BLADDER FOR RADIAL INDUSTRIAL & OTR TIRE
- B TYPE CURING BLADDER FOR BIAS AGRICULTURAL (AG) TIRE
- B TYPE CURING BLADDER FOR MERIDIAN AGRICULTURAL (MG) TIRE
- B TYPE CURING BLADDER FOR MOTORCYCLE TIRE
- B TYPE CURING BLADDER FOR CYCLE/MOTORCYCLE TIRE
BUTYL RUBBER A TYPE RADIAL TYRE CURING BLADDER FOR PCR & LTRDetail Information
The tyre curing bladder (hereinafter referred to as curing bladder) is an essential tool in vulcanization of tyre.
The quality of the curing bladder is closely related not only to the production cost but also to the quality of tyre.
In order to extend the curing bladder service life and avoid unnecessary losses, please refer to instructions carefully.
1. Please check whether the package is complete and the curing bladder size is clearly identified before storage.
2. Please inspect the curing bladder according to the “Tyre Curing Bladder Standard”(Q/JTD001 -2003) we have provided or according to the contract requirement.
3. Each curing bladder is attached with a Tyre Curing Bladder Performance Record Form in each bag or each case.
4. If you find the goods do not meet your requirements, please keep them as they are and contact us immediately so that we can provide faster and better service for you.
Storage Conditions ：
5. In order to avoid possible deformation during long-time storage, the height for bagged curing bladders must not exceed 6 layers or 2500mm.
6. Store the curing bladders under room temperature, keep them away from chemicals and heat sources, prevent them from sunlight, and what’s more, curing bladders must be kept away from any oil.
7. It is better not to open the case 48 hours before use in case the storage conditions are in conflict with the above article 6.
8. The OTR curing bladder must be resumed to its original shape before being put in storage.
9. Please take care to prevent curing bladders from any sharp objects to avoid any possible hard damages under storage and transportation conditions.胶囊代号适用轮胎规格花纹类型Curing Bladder DimensionCuring Bladder Mounting Dimension断面周长LB(mm)外直径DB (mm)总高度HB (mm)冠部厚度to(mm)颈部厚度to'(mm)夹缘内径dB(mm)夹缘高度a(mm)夹缘宽度b(mm)Bladder CodeApplied Tyre SizeVents/ Etching TypeEffective Periphery LB(mm)Outside Diameter DB(mm)Overall Height HB(mm)Crown Gauge to(mm)Neck Gauge to'(mm)Foot ID. dB(mm)Foot Height a(mm)Foot Width b(mm)A12"x243x515PITTED SURFACE4605002904.59.030014.515.0A12"x243x515PITTED SURFACE4165353104.59.030014.515.0A12"x250x565PITTED SURFACE4845653204.89.030014.515.0A14"x270x530-1PITTED SURFACE4755303304.88.532915.015.5A14"x270x530-2PITTED SURFACE4755303304.88.532915.015.5A14"x300x550-1PITTED SURFACE5095503504.88.532915.015.5A14"x300x550-2PITTED SURFACE5095503504.88.532915.015.5
Recommendations for achieving best Bladder Performance:
FENGFU Bladders are manufactured using a well proven long-lasting heat conductive butyl rubber compound.
The high degree of elasticity of the bladder guarantees trouble-free molding and stripping.
The following points should be considered under all circumstances:
10. We suggest that you store the curing bladder at least 90 days from the date of production before use.
11. Please resume the curing bladder to its original shape 24 hours prior to use.
12. Before mounting curing bladders, please check whether the curing bladder size match as the tyre size. We suggest you choosing the proper clamping size as per curing bladder clamping parameters.
13. Before mounting bladders into curing press we recommend to pre-treat the bladders with a bladder coating material to optimize your curing bladder performance and extend the curing bladder life time.
14. Spraying of isolation agent inside the green tyre is necessary in order to avoid sticking, trapped air or stripping problems
15. We suggest you do not use any lubricants during clamping the curing bladders, please pay attention not to use any diluted water-solubility silicon latex and not to drop it on the tyre mould surface.
16. When you test the curing bladder air tightness, the elongation of curing bladders should be proper in order to avoid destroying the curing bladder or causing other problems.
17. The strict deoxidization of overheated water and nitrogen vulcanization can evidently extend the curing bladder service life.
18. Before tire curing starts, the bladder should be fully warmed up. For this, the machine should be operated according to the press manual.
19. In case of pre-inflating during the warm up, the bladder outside diameter must not exceed the tire sidewall plate outside diameter of the tire mold, in order to avoid non-symmetric deformation.
20. If the bladder has cooled down after an interruption in the curing process, it is imperative to warm it up again.
21. Please fill in the Curing Bladder Performance Record Form seriously, in order to get better service when curing bladders quality problem come out .
To optimize your bladder performance furthermore we recommend the application of a permanent bladder coating material .
We can offer you various coating material applied on our bladders.
For our customers,we offer one-stop service to optimize bladder application and performance.
In case of any questions , please contact us freely.VENTS/ETCHING TYPEPEBBLE SURFACEExcellent venting to prevent trapped airMinimum inner liner consumptionThe smooth and simple final tire inspection due to constant surface structureVENTS/ETCHING TYPEPEBBLE SURFACEExcellent venting to prevent trapped airMinimum inner liner consumptionThe smooth and simple final tire inspection due to constant surface structureVENTS/ETCHING TYPEPITTED SURFACEWarehouseEquipmentTYRE CURING BLADDER :INJECTION A TYPE RADIAL TYRE CURING BLADDERINJECTION B TYPE RADIAL TYRE CURING BLADDERINJECTION AB TYPE RADIAL TYRE CURING BLADDERRADIAL TYRE CURING BLADDERB TYPE BIAS TYRE CURING BLADDEROTR RADIAL TYRE CURING BLADDEROTR BIAS TYRE CURING BLADDERAGRICULTURAL TYRE CURING BLADDERAIR SPRING CURING BLADDERAccept customizationPlease download the tyre curing bladder catalogue for specific classfication.Interior Packaging:Plastic bag or Woven bagAccept customizationExterior Packaging:Plywood case or CartonAccept customizationInterior Packaging:Plastic bag or Woven bagAccept customizationExterior Packaging:Iron case or CartonAccept customizationNavigation